Presented For Sale By:
Presented For Sale By:
|Model||Swan 90-707 S|
|Location||San Giorgio di Nogaro, Italy|
|Tax Status||Tax Paid|
This remarkable Swan 90 has been equipped to the highest possible level with an incredible list of options, no expense has been spared and no short cutstaken. Full carbon fibre hull and deck in semi-raised saloon configuration, she is well set up for short handed sailing with an in-boom furling mainsail and lifting keelthat reduces her draft to only 3 metres (9’6”) Bow and stern thrusters facilitate maneuvering and twin generators provide ample power. Presently lying in the NorthernAdriatic, she is offered for sale in EU VAT Paid status and is available for immediate delivery.
Swan 90 S - Red Sula
LENGTH OF WATERLINE
DRAFT (Lifting Keel)
4.40 Keel Down
3.00 Keel Up
14.44 Keel Down
9.85 Keel Up
Volkswagen V8 4.2L 285 Hp (212 Kw)
FUEL 1630 Lt, WATER 1000 Lt, Holding 400Lt, Hot Water, 130Lt
DC 24 V : AC 230V
MAST & BOOM
Offshore Spars Intermediate Modulus Carbon Fibre Mast
Future Fibres PBO Standing Rigging, Marten Leisure Furl boom
Adriatic Coast, Italy
Germanischer Lloyds 100 A5 Sailing Yacht
€ 8,750,000 VAT Paid
HULL & APPENDAGES
The hull is constructed in carbon fibre/epoxy laminate, the top sides are of sandwich construction. The bottom laminate from the waterline down is monolithic.
Hull above the waterline is finished in Snow White Awlgrip paint with Red stripes on top of a epoxy primer. Below the waterline, two coats of hull guard epoxy primer have been applied under two coats of white antifouling
Structural bulkheads are of pre-preg foam cored carbon sandwich construction laminated to hull and deck. There is one water tight door in each structural bulkhead forward of the raised saloon which divide the yacht into seven different individual compartments with their own bilge pumping system
The ballast bulb is an antimony lead casting and attached to a steel fin. The keel can be hydraulically raised by approx 1.4m from a max draft of 4.4m. It is either locked in raised or lowered position by a hydraulically operated locking system
The twin rudders are built using carbon fibre/epoxy skins on foam core, with a tubular carbon fibre stock. The rudders are supported by self-aligning bearings supplied by JP3. The lower bearings have double seals to prevent leakage. Lightweight aluminium steering quadrants bolted to rudder stocks.
Two custom built composite pedestals with compass, navigation and sail control systems. Two 1200 mm clear coated carbon composite wheels with elkhide covered rim. The wheels can be independently disconnected.
The transom door doubles as a bathing/boarding platform. carbon fibre pre-preg construction for maximum stiffness with 9 mm teak on the topside. The door is hydraulically operated by two custom built stainless steel rams. Two stainless/teak ladders, one to provide access from deck to the platform, the other a swimming ladder. Hot/Cold water shower on swim platform.
The starboard side hatch conceals a Swiss Carbon hydraulically operated telescopic gangway with articulation both vertically and horizontally. Port side hatch for shore power, telephone, dive compressor and water connections
Storage space with carbon fibre lightweight floorboards accommodating Williams 3.2m jet drive tender and remote controlled hydraulic winch for hauling inboard
Storage for sails and equipment, carbon fibre lightweight floorboards, topsides faired and top coated
Carbon fibre / epoxy deck laminate using core cell foam core with high density core under the deck fittings. Coaming and coach roof are painted white using Awlgrip paint system, Coaming stripe red Awlgrip. Laid teak 65 x 9 mm nominal thickness, quarter cut, battens on side decks, coamings and cockpit sole glued and vacuum bagged
Sail Handling Hardware
Deck gear by Harken. Genoa tracks recessed into teak deck, double foot blocks for genoa and gennaker sheets. Harken 150 standup blocks for halyards, gennaker sheets and runners. Five Spinlock jammers for halyards
All winches are hydraulically driven via the hydraulic main ring system and connected to the valve blocks with flexible hoses.
Four Harken B1110 STCAA HLHY winches in cockpit, primary & secondary
Two Harken B990.3 STR HY halyard winches near the mast
One Harken CR33-2 Speed captive mainsheet winch in lazarette
One Harken CR33-2 Speed captive main halyard winch in the bilge forward of the mast
Lewmar Vertical 4000 hydraulic windlass in anchor locker
Sanguinetti hydraulic retractable capstan mooring winch on foredeck
Hydraulically operating Titanium anchoring arm for stowing the bow anchor in deck locker. The controls are on the same wandering lead as the windlass. The pulpit and push pit are 610 mm high with spacing according to ISAF/ORC requirements and made of a Ø 32 mm stainless steel tube. The push pit has gates for easy access to bathing platform / gangway.
Cleats and fairleads
There are eight 400 mm Versari & Delmonte aluminium pop-up mooring cleats; two on fore deck, four amidships, two aft. Pop up stainless steel fairleads integrated into toe rail, two forward, four amidships and two aft.
Nautor custom made flush mounted tinted acrylic hatches with gutters and frames in white painted composite. All hatches are supported by gas cylinders, sizes are for clear openings. Escape hatch in aft cabin above bed. There are six Goiot Cristal 43-18R openable tinted acrylic portholes in coamings, flush mounted with white painted aluminium frames. Nautor custom made teak covered hatches for access to deck lockers and lazarette
Deck house windows
Parasol grey deckhouse windows made by Form glass, chemically toughened, laminated and glued to the superstructure. Main companionway lockable sliding hatch of tinted acrylic with sliding drop board. The lockable main companionway has a sliding hatch of tinted acrylic and a GRP sliding drop board.
Aft cockpit is recessed into deck, forward cockpit with two U-shaped settees and two varnished teak cockpit tables that can be lowered to seat level to create an expanded sun bathing area
Sprayhood recessed with a canvas cover over the main entrance. Removable bimini over center cockpit. Covers for steering pedestels, wheels, cockpit tables and mainsail.
Mainly teak is used for visible interior and has a waxed natural effect finish. Vinyl covered removable overhead panels are installed in all accommodation areas. The same material is on the inside of the coach roof coamings, Italvipla Roma Col. 6. The floorboards are of PVC-sandwich construction and the top face is teak and finished in the same colour as the rest of the interior. All floorboards are laid on vibration damping materials.
Hardware and outfit components are of a type designed to eliminate rattling or hanging. The cabin doors are provided with double action locks and with catches to hold them in open position where possible.
All locker doors are fitted with high quality furnishing hinges and are kept closed with push button latches. Doorstoppers are fitted where needed. Automatic lights in hanging lockers
All bathroom mirrors are made of a special marine quality glass. Edges sealed to prevent moisture intrusion. All openable deck hatches are fitted with manual roller blinds and mosquito screens.
Partitions are of sandwich construction on a core of 30 mm foam. Skin panels of 5 mm marine plywood with 0.6 mm wooden veneers.
Overhead LED lighting throughout yacht, LED reading lamps at each berth, Red nightlights throughout.
Forward Cabin (Crew Cabin)
Upper and lower berths in starboard section, hanging locker forward of berths. Centerline bulkhead with TV, folding table and lockers mounted on port side. Port section equipped with settee and dining table with Pullman berth above. Independent access to deck via 80cm x 80cm hatch with ladder. Head compartment forward with shower, mirrors, storage lockers and vacuum WC.
Forward Amidships Cabin (Guest Cabin)
Guest cabin starboard side forward of saloon with queen sized double berth outboard and a folding Pullman berth above. Storage lockers and drawers built into berth. Folding table and storage ockers built into inboard bulkhead. Hanging locker forward of berth, ensuite head compartment with separate shower stall, sinks, heated towel rack, mirrors and vacuum WC
Aft Amidships Cabin Starboard (Guest cabin)
The starboard cabin has two single berths. There is a full height hanging locker forward of the outboard berth and upper lockers above the outboard berth. Drawers are placed under the berths where practical. En-suite head compartment forward with washbasin, mirrors, storage lockers and vacuum WC
Aft Amidships Cabin Port (Guest cabin)
The port guest cabin is equipped with twin berths with a table between. Full height hanging locker aft of outboard berth with built in storage drawers. En-suite head compartment aft with separate shower stall, washbasin, mirrors, storage lockers, heated towel rack and vacuum WC.
Aft cabin (Owner’s Cabin)
Queen sized berth on centerline with bedside tables on port and starboard, hanging locker with chest of drawers on lower part located starboard and port. Settees on both starboard and port, vanity desk on starboard side. Air conditioning integrated into overhead panels to achieve low air speed. Head compartment forward and port contains separate shower stall, vacuum WC, bidet, sinks, mirrors, heated towel rack and storage lockers
Dining for eight persons on port side with a U-shaped settee outboard port and a large rectangular dining table with two folding seats. There are four lockers, one in each corner of the saloon port side. Stowage under settees are placed where practical.
Day head compartment aft and starboard with vacuum toilet, mirrors, wash basing and storage lockers
The saloon dining table size is approx 800 x 1850 with drawers under table top for cutlery.
Navigation table on starboard side forward of settee with electronic, PC and communications systems discretely installed. Nav seat stows neatly inside cabinet.
The galley is located on the port side of the yacht forward of saloon with access to engine room, saloon and crew quarters. Two sinks and dishwasher are located inboard, stove top and work surfaces outboard, crew companionway located forward with washer and dryer installed outboard behind panels. Main electrical panel is located aft and outboard. Drawers and storage lockers
- 2x front loading refrigerators 107 L
- 2x front loading freezers 95 L
- 2x drawer refrigerators 90L in saloon
- Miele induction stove with steam oven
- Overhead exhaust hood
- Food waste disposal integrated with sink.
- Quooker boiling water tap
- Washing machine
The engine room is located on CL below the saloon. The structure is built in aluminium profiles with entrance from galley. Engine room surfaces and technical equipment are painted white
Partitions between cabins, toilets, corridors, etc. are built to meet a 20 dB reduction of airborne sound.
The engine room is insulated towards cabins and saloon with various layers of rock wool with noise barrier sheets in between. The engine room door is of similar construction as the surrounding partitions. They close onto rubber faced landings for maximum noise reduction.
ENGINE & SYSTEMS
Volkswagen V8 4.2L 285Hp turbo charged diesel engine with direct mounted reduction gear. Engine reduction gear are supported on flexible mounts. ZF W220 reduction gear with parallel input and output shafts, 24v clutchable PTO for hydraulic pump 250Nm torque. Aquadrive CV42 drive shaft between gearbox and propeller pitch control unit, down angle of 7 degrees for the pitch control unit and 75mm prop shaft. Hundested VP type FR-HP 800mm propeller with feathering position
The feed lines to the engine and diesel generator are equipped with 30-micron fuel filter/water separators with water alarm. Dual version mounted for main engine so as to permit uninterrupted running of the engine while changing filter elements. Single version for diesel generator, vacuum gauges with water alarm mounted.
All flexible hoses are according to ISO7840.
Fuel capacity 1630 L in two in stainless steel tanks, with individual level indicator. Filler line on starboard side. Tanks are equipped with hatches of adequate size to permit inspection
and cleaning. All tanks are pressure tested to 0.3bar. Shut off valves are provided for each tank.
The Halyard exhaust system has fibreglass silencers and gas/water separators installed for both main engine and diesel generator. Water is discharged below the waterline and exhaust gases from main engine and diesel generator exit under the transom. Silencers are provided with a drain tap. They are flexibly supported on vibration dampening brackets. The silencer / separator system is a custom Halyard design with lift silencers and flat separators.
Two 20 kW M864W Northern Light generator producing single-phase 230 V 50 Hz AC. The units are mounted on elastic seating.
Hundested FT2R bow thruster powered by the hydraulic PTO pump on the diesel generator, 42.3kW hydraulic power
Hundested FT2R bow thruster powered by the hydraulic PTO pump on the diesel generator, 42.3kW hydraulic power
Fire Fighting System
There is a total flooding Clean Agent FM200 fire extinguishing system for engine room space with manual remote control. Two fire hydrants with hose reel, one forward and one aft.
The hydraulic system is a Bosch-Rexroth custom designed system to supply all hydraulic functions quietly and smoothly, eliminating any inherent hydraulic noise. The alternative power sources are installed to meet the demands of the sail handling equipment. Central hydraulic system is PLC controlled.
The hydraulic system is defined on a basis of a central power pack supplying regionally located valve groups, thereby achieving minimal weight to power ratio with the effect of using minimum electrical power with maximum hydraulic movement. Each control valve group is situated close to the operating unit, giving a precise control and allows for a quiet and smooth operation, eliminating inherent hydraulic noise and vibration. The system has two different sources of power. Each source will be operated independently of each other. The sources are obtained from:
1. Generator PTO pump Bosch-Rexroth A10V045 on each genset, 22kW each
2. Two DC Electric motor standby pump units Bosch-Rexroth A10V028, 5 kW each
3. Main engine pump Bosch-Rexroth on gearbox PTO (56kW)
All pumps are equipped with a horsepower controller. The function is based on the power requirement from the users with the style of maximum speed/ minimum pressure and maximum pressure/ minimum speed. The alternative power sources are installed to meet the demands of the sail handling equipment. Since the sail handling is dependent on hydraulic systems it is important to have alternative power sources to ensure trouble free operation.
- Anchor windlass
- Lifting keel and lock
- Forward mooring Sanguinetti
- Jib furler
- Anchor swing arm
- Bow thruster plus up/down
- Stern thruster plus up/down
- Autopilot back up, supplies oil to auto pilot cylinders from a genset PTO pump.
- Jib halyard tensioner
- Backstay tensioner
- Mainsail in-boom furler and lock
- Main halyard captive winch
- Boom vang
- Starboard halyard winch
- Port halyard winch
- Primary and Secondary winches
- Genoa Car Pullers
- Main sheet captive winch
- Transom hatch cylinders
There is one low pressure (6 bar) piston compressor with quick acting couplings in lazarette for transom door air seal plus connection points in engine room and forepeak. The piston compressor is a Thomas 327 CDC 56/24.
All systems are based on reliable components with world wide service. Components and valves are labeled with function, and piping is labeled with colour code, including an arrow to indicate direction of flow.
Fresh water System
A pressurized hot and cold water system is installed. The fresh water piping is of polypropylene, nylon and copper tubing. Filler line on side deck is led to a valve chest. The valve chest has valves for each water tank and for water pressure pumps. Hot and cold water is distributed to all heads, to the galley and to deck shower. Cold water deck wash, one fwd and one aft. There are single lever mixing faucets for wash basins, galley sinks and showers.
There are two stainless steel tanks with a total capacity of approx 1000 L. The tanks are provided with baffles, hatches, level indicators and vent pipes. All tanks are pressure tested to 0.3 bars. Tank levels are shown on electrical main switchboard.
The water pressure system is equipped with two Reya A95, 24 V pumps. One 24 l pressure tank is connected to the system. There is a city water connection that allows shore water supply to be piped directly into the pressure water system via a pressure regulator and check
Hot Water System
Hot water tank 130 litre capacity with three individually operated heating elements. The hot water pipes are insulated with pipe insulation, hot water circulation quickly distributes heated water throughout boat. Inlet has a check valve to prevent hot water back flow. Outlet has a relief valve for over-pressure protection. There is a thermostat mixing valve to prevent too hot water in the system.
The water maker is an Idromar Mini Compact model MC5S, vertical version. The water maker produces 230 l/h (5520 l / 24 h), installed in the engine room. The water maker is provided with dual pre-filters, primary with 25 micron cartridge, secondary with 5 micron cartridge and fresh water flush. The feed water pumps are self priming with sea bronze body and internal
parts in stainless steel AISI 316. The high pressure pump is constructed to work with sea water.
Sea Water System
There are sea cocks of bronze for all through-hull connections below waterline located in accessible position. Inboard side of sea cocks fitted with stud long enough to take two hose clamps.
There is an electrical fire/anchor wash pump with connections on fore and aft deck. G&R type CB 25/16 24 VDC, capacity 180 l / min. There are two fire hydrants with hose reel, one forward and one aft.
Grey Water System
Grey water from sinks, basins, showers, air conditioning and washer/dryer is collected in two stainless steel grey water tanks, total capacity 400L. Level switches are fitted to each tank, with indication at ¾ full and full. The grey water tanks are emptied by 24 V electrical pumps to sea cocks via siphon breaks
Black Water System
All toilets are connected to the black water tank. Two stainless steel black water tanks are provided, one for aft toilets and one for forward toilets, total capacity 200 l + 200 l, with indication at 3/4 full and full. The tanks are fitted with baffles, inspection covers, and vent lines. Tank ventilation equipped with SaniGard vent filter. The tanks can be emptied by 24 V electrical pumps to sea cocks via siphon breaks. Each tank is also provided with a deck suction line.
The toilets are Tecma Standard Plus, 24 V. Flushing by fresh pressure water, consumption per flush about 2.5 litre. The function cycle is completely automatic. The high performance turbine pump enables a complete fragmentation of the organic residues. Full black water tank disable flushing of toilets.
Bilge Pump Systems
There are six separate bilges, i.e. fore peak, forward cabin, engine room, saloon, aft cabin and lazarette bilges. Each bilge is equipped with a DC driven submersible pump 140 l / min. Two manual Whale Titan, 100 l / min are installed as back-up pumps, one for fore peak and forward bilge, the other for aft engine room and lazarette bilge.
Whale gulper drainage pumps are installed in forepeak, forward area, mast area, engine room, aft area and lazarette to ensure maximum dryness.
A central cooled / heated waterborne system 230 VAC 50 Hz is fitted for the entire accommodation. Condensation water from the system is collected to the grey water tanks. The system is designed to operate in Mediterranean climate conditions.
The total cooling / heating capacity is divided in proportion to cabin volume and position. The system is designed for air handler to run on low speed for silent operation. There is an individual temperature control in each cabin. The main unit is a Condaria PWM/FCL/18002, 72 000 BTU/h (21 kW).
Forced air ventilation system in all cabins
There are four custom made Frigonautica 24V DC water cooled compressors units for fridges and freezers, two additional drawer type refrigerators installed 90L each.
The electrical components are chosen based on the Yards long experience in the yachting industry. Special attention is given to reliability and world wide service ability. Electrical diagrams will be delivered with the yacht, for both DC and AC systems and showing the location of all junction boxes. Cables are labeled with identification numbers at both
ends. At watertight bulkheads wires are run up to deck head height when penetrating the bulkhead or are sealed in place to produce water tightness.
Mast and shrouds are electrically connected to the keel. In the top of mast is an air terminal connected to a lightning conductor, which runs down to the keel. The prop shaft, keel and thruster have their individual sacrificial anodes.
Power supply of 230 V 50 Hz single-phase three-wire AC-system. The 230 V system can be fed by the diesel generator or shore power inlet. The bus is of split bus type. There are also a number of 230 V 50 Hz appliances fed through DC/AC inverters.
Shore inlet plug, 230 V 3-pole 63 A is accessed through a hinged lid at transom. Shore power cable is 15 m long. There is a separate shore inlet for air conditioning. For the separate air
conditioning inlet, a galvanic insulator is installed in the ground wire. Power from ashore is led to a 15 kVA isolation transformer.
There are two 20 kW M864W Northern Light generator producing single-phase 230 V 50 Hz AC. The unit is mounted on elastic seating. The generator is mounted inside proprietary sound shield.
There are three Mastervolt, Mass 24 V 100 A chargers with 3-step charge characteristics, for the service battery. There is one Mastervolt, Mass 24 V 100 A charger with 3-step charge characteristics, for hydraulics battery. The starting batteries can be charged by one Mastervolt Mass 12 V 10 A charger with 3-step charge characteristics via isolator diode.
Conversion of 24 V DC to 230 V AC 50 Hz for single-phase AC consumers. There is one Mastervolt 24/2500 VA for misc. and one Mastervolt 24/1500 VA for instruments and entertainment. Both inverters have a separate transfer switch.
There are 230 V outlets of schuko type. One outlet per toilet, two outlets per cabin, three in galley, four in saloon, one in engine room, one in sail locker and one in the port side lazarette.
2-pole 24 V insulated return DC-system for lighting, blowers, pumps etc. The wires are sized to minimize voltage drop. There are two battery banks, one for service and one for hydraulics. The service battery bank is 24 V 1040 Ah /1h, Valence Lithium type powering lights, blowers, pumps, electronics etc. The use of lithium batteries saves 748 Kilograms from the sue of standard gel type batteries. Hydraulic batteries are Optima 300 Ah / 20 h and consist of eight Optima Yellow Top S5,5 12 V 75 Ah. The hydraulic bank is used for the 2 x 5 kW central hydraulic and the auto pilot pump. The battery banks are located aft of the engine room.
There is one 24 V 140 A Bosch alternator on the main engine common for service and hydraulics battery banks, through a battery isolator. The hydraulics battery is charged by the main engine alternator through splitting diodes.
24 V DC outlets, one in the port side lazarette, one in engine room, one in anchor locker, one on the mast and one in aft cockpit.
Plumbing & Monitoring Sytems
The alarms are presented on a display in the navigation area for the following components:
- Fresh Water tank level
- Fresh Water pump run dry
- Sea Water pump run dry
- Grey water tank level
- Grey pump runtime
- Black water tank level
- Bilge level alarms
- Bilge pump runtime
- LPG gas alarm
- Fuel tank level
- Water in Fuel separator
- Hydraulic oil level
- Hydraulic oil temp
- Low Battery voltage
- Generator overload
There is a separate fire alarm system with one sensor at the aft entrance, one in the engine room and one at the main entrance.
Two Suunto 5” magnetic steering compasses at helm adjustable for global balancing.
A C. Plath Navigat X Mk2 gyrocompass as the main heading source for the navigation instruments, autopilot and other instruments requiring accurate heading information. A B&G Halcyon gyrocompass is used as the backup heading source.
There is a comprehensive Brookes & Gatehouse Hercules 3000 package consisting of central processor unit, 1450mm masthead unit, speed/temperature sensor, depth sensor and barometric sensor. B&G Hercules H3000 Main processor and a Halcyon gyro processor. Barometric pressure is displayed in the B&G H3000 system.
One B&G Graphical Function Display (mono-chrome GFD) and one NMEA Full Function Display (FFD) located at nav station. One GFD display in aft cabin and one in crew cabin
Four 40/40 repeaters mounted on the mast.
Four 30/30 repeaters in aft cockpit
GFDs also display hydraulic pressures for backstay, vang, outhaul, jib halyard, inner forestay as well as forestay length adjuster position.
B&G 360° and 45° analogue wind direction displays on each side of cockpit backrest.
GPS & Radar
A Furuno NavNet radar/chart plotting system consisting of one Furuno 1834C/C-MAP radar/plotter display at the navstation.
Furuno chart plotter / radar at each steering console
Furuno GP-320 DGPS to be used as the main navigator for:
- Furuno NavNet radar/chart plotting system
- PC cartography software MaxSea NavNet Commander V12
- Brookes & Gatehouse
- Brookes & Gatehouse autopilot system
A Furuno GP-37 GPS navigator with WAAS software as back-up.
Radar is a Furuno 4 kW 60 cm radome type antenna integrated with the Furuno NavNet plotter system.
PC cartography software MaxSea NavNet Commander V12, on the computer. The MaxSea NavNet software can also be viewed in the saloon TV. The chart system for the Furuno NavNet system is C-MapNT MAX.
Dual frequency Navtex receiver, Furuno NX300.
Furuno FA-150 class A type AIS system. The target information is sent to the Furuno NavNet system and integrated with the MaxSea NavNet software.
The Furuno NavNet GP-320 DGPS antenna on the port lower pushpit rail.
The Furuno GP-37 GPS antenna is mounted on starboard 2nd spreader.
The Furuno FA-150 AIS GPS antenna is mounted on port 3rd spreader.
The Furuno NavNet radar scanner, 60 cm dome type, is mounted front of mast between 1st and 2nd spreader.
The Furuno NX-3H-D Navtex antenna is mounted on 2nd spreader port side.
Auto Pilot System
B&G H3000 ACP2 autopilot system with one Graphical Pilot Display (mono-chrome GPD) control unit at each steering wheel. Powered by an individual 24V Marsili/ Bosch Rexroth power pack driving the steering quadrant via twin Rexroth low friction cylinders. There is a hydraulic back-up for emergency use, supplied from the main hydraulic system.
The Simrad RS-87 DSC VHF has two handsets, one at the nav station and one at the helm, with intercom possibility between the two. Handheld Simad VHF radio.
KVH Fleet Broadband 250 for data/fax/phone
Cellular Phone Systems
Nokia E60 quad band GSM phone with internet capability
ICOM PCR-1500 communications receiver for weather fax and navtex
TEAC sound system with Ipod connection, linked to LCD TV
Bose Lifestyle 48 DVD/CD/FM stereo system, stores up to 350 CDs on hard disk, connected to pop-up LCD TV
Four Bose 32SE speakers installed in cockpit, fed by saloon hi-fi system, controlled by personal music center remote control
TEAC sound systems with IPod docks linked to LCD TVs
Pop-up mounted 40” Sony LCD TV with Pal/SECAM tuner connected to the Delta antenna for terrestrial TV and to the KVH M3 satellite TV antenna system for European free to air satellite TV.
Sony 40” LCD TV connected to Delta and M3 antennas
Lava 15” LCD TV connected to Delta and M3 antennas
Two Dell Optiplex GX 745 “Ultra small form factor” computers with DVD station connected to 19” LCD flat screens at the navigation station, one for communication, one for navigation.
A HP Deskjet 450 printer is provided for hardcopy printouts.
IR intruder detection in all cabins connected to the alarms plc, fog horn and spreader lights signal alert. Security cameras mounted at mast head, spreader and engine room.
MAST & RIGGING
Four spreader mast with discontinuous shrouds by Offshore Spars, faired and painted white. The rig is set up for easy handling with swept spreaders 25 degrees. The Boom vang is used on the wind to complement mainsheet. The mast is a carbon fibre intermediate modulus, with luff track for mainsail. The masthead is a moulded carbon fibre unit integral with mast. There is an R&R Electronic Delta DSC Biscaya active antenna at the masthead for the VHF, TV and FM radio. Marco EW3 24 V foghorn.
I = 36,80 m
J = 10.76 m
P = 35.50 m
E = 11.45 m
Mainsail in-boom furling built by Marten Spars, boom and furling mandrel in carbon fiber Hydraulic operation
There is a boom preventer system and built-in deck lights.
Future Fibres PBO Rigging. Main shroud rigging screws of barrel pin type. Forestay in Navtec Nitronic rod, genoa furling foil in carbon fiber.
All Ropes are Dyneema, screw shackle for main halyard, all other Tylaska Snap Shackle
All Halyards Internal
1x Main sheet
2x Jib sheets
2x Staysail sheets
2x Gennaker sheets
2x Gennaker halyards
1x Staysail halyard
2x Jib halyard
1x Mainsail halyard
2x Running Backstay tails
1x Trysail halyard (Gantling)
2x Trysail sheets
2x Inboard reef lines
2x Outboard reef lines
All the hydraulic functions are powered by central hydraulic system. All Navtec cylinders are black anodized
- Reckmann UD4 Sphere hydraulic furling head stay with R6 double groove Carbon foil.
- Navtec cylinder for inner forestay tensioner, Navtec -40 SE.
- Navtec boom vang, Navtec -90
- Navtec jib halyard tensioner, Navtec -30 FE
- Mainsail outhaul, Navtec -22 FE.
- Cunningham Navtec -17 FE
- Two cylinders with mechanical locks for split backstay adjustment, 2x Navtec -30 L.
- Removable hydraulic mast jacks with spacer and removable manual pump.
Owner's Manuals are provided in with directions for use and maintenance, drawings and diagrams for main systems and handbooks for machinery and components.
Anchoring and Mooring
- One CQR 180 lbs anchor on hydraulically powered swinging titanium anchor arm
- Fortress FX-85 stern anchor
- Removable composite bow protection
- 100 m 12 mm high-tensile anchor chain
- 100 m 25 mm plaited nylon anchor line
- Four mooring lines 15 m each, diameter 22 mm
- Four mooring lines 30 m each, diameter 22 mm
- Eight Avon air fenders with lines
- Anchor day shape and light with cable and plug
- Two floating boat hooks
- One removable MPS block Harken C5813 ø150 mm on C7403 base
- Four screw in deck eyes for outboard sheeting
- Four 10" double grip and four 10” single grip winch handles
Man Overboard Module mounted on stern pushpit
Two eight-man AVON Modula 8 Supervacuum packed life rafts.
Portable fire extinguishers Gloria P2G for each cabin and a fire blanket in galley.
EPIRB with GPS
Search and Rescue Transponder
6x McMurdo personal locator beacons with homing antenna
Sails by North Sails
3DL Marathon Mainsail, Staysail & Furling Genoa
Gennaker with sock
Spares and Tools
Basic spare part kits provided for Engine, Generator and other systems
Basic engine and generator tool kits are provided.
Four handles for opening deck hatches and four suction lifters for floorboards.
Sounding rods for fuel and water tanks are provided
2x bosun’s chairs
Bauer Dive bottle compressor in port side lazarette
3.25 metre Williams Jet-drive tender which stows in lazarette
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information. This vessel is offered subject to prior sale, price change,or withdrawal without notice